ET200BR series Pump.
(and E201 through to E215 pumps)
Page Content
E200 series pumps
E300 series pumps
E400 series pump.
E500 series pump.
ET3000/3009 series pump.
MTP 600 pump
General Features
Electrical Connection
(A.C.) through a diode. The connection has to be made as shown on the diagram.
(D.C.) requires the use of a square waves impulse converter
THREE POLE PLUG CONNECTOR UNI 4400 (DIN 43650B) - IP 65
Coil polybutylene terephtalate glassfibre loaded insulation class I THERMIC CLASS: H (180 degrees C: VDE) F (155 degrees C: UR)
Mounting Position Any.
Tube guide Brass
Piston and Spring Stainless Steel high corrosion resistance
Sealings Silicone
Sliding Guide NBR
Ambient Temperature 80 degrees C (VDE), 25 degrees C (UR)
Fluid Temperature 35 degrees C
Fluids Water and non corrosive media.
Suction prevalence 50 cm
Tolerance all the performances apply within a tolerance of plus/minus 15%.
E407 series Pump.
(E300 and E410 spec in chart below)
General Features
Electrical Connection
(A.C.) through a diode. The connection has to be made as shown on the diagram.
(D.C.) requires the use of a square waves impulse converter
Coil polybutylene terephtalate (PBT) insulation class II
THERMIC CLASS: F (155 degrees C: UR)
Mounting Position Any.
Tube guide Polyamide (PA)
Piston and Spring Stainless Steel high corrosion resistance
Sealings NBR
Sliding Guide NBR
Ambient Temperature 70 degrees C
Fluid Temperature 60 degrees C
Fluids Water and non corrosive media.
Suction prevalence 1 meter
Tolerance all the performances apply within a tolerance of plus/minus 15%.
E507 and E512 PUMP
General Features
Electrical Connection
(A.C.) through a diode. The diode could already be incorperated in the coil (D.C.) requires the use of a square waves impulse converter.
Coil polyamide (PA) or polybutylene terephtalate (PBT) or polyester (PET) insulation class II
THERMIC CLASS: F (155 degrees C: VDE), A (105 degree C: UR) The coil is provided with a pocket for the thermoswitch in series connected to the line terminal to prevent overheating of the coil.
Mounting Position Any.
Tube guide Polyamide (PA)
Piston and Spring Stainless Steel high corrosion resistance
Sealings EPDM NBR (514)
Sliding Guide PTFE, EPDM (E503, E504, E505)
Ambient Temperature 70 degrees C (VDE - UR), 50 degrees C (VDE - UR: 504,505, 507)
Fluid Temperature 60 degrees C (VDE - UR), 35 degrees C (VDE - UR: 504, 505, 507)
Fluids Water and non corrosive media.
Suction prevalence 1 meter
Tolerance all the performances apply within a tolerance of plus/minus 15%.
Special Execution: Outlet tube in brass.
ET 3000 AND ET 3009 PUMP
Both pics are of the ET3009
MTP 600 PUMP
General Features
Electrical Connection
(A.C.) through a diode.
(D.C.) requires the use of a square waves impulse converter.
Supplied with THREE POLE PLUG CONNECTOR UNI ISO 4400 (DIN 43650A) - IP 65 with diode.
Coil
polybutylene terephtalate (PBT)
insulation class: I
Thermic class H (180 Degrees)
The coil is provided with a pocket for the thermoswitch in series connected to the line terminal to prevent overheating of the coil.
Mounting Position: In any position, preferably the horizontal one.
Tube Guide: Stainless Steel.
Piston and Spring: Stainless Steel high corrosion resistance.
Sealing: FKM, H-NBR
Sliding Guide: PTFE, FKM (3000)
Ambient Temperature 50 Degrees C. (3000), 70 Degrees C (3009)
Fluid Temperature 25 Degrees C. (3000), 60 DegreesC (3009)
Fluids: Water and non corrosive media.
Suction Prevalence: 1 meter.
Tolerance: All the performances apply within a tolerance of Plus/Minus 15%
Special Executions: Voltage 120V 60HZ.
General Features
Standard Voltages: 120V 60Hz, 230V 50-60Hz, 100V 50-60Hz.
Thermic Class: F (155 Degrees C.)
Electrical Connection: IP44 Standard cable lenght 120 cm.
Mounting position: Horizontal.
Motor: Single Phase or Threephase, 2 Pole induction.
Execution: With Fan, MEC 56 - with mounted capacitor 5 uf) - built in overload motor protection (140 Degrees C)
Materials: Shaft: stainless steel with improved corrosion resistance. Impeller: brass nickel - teflon loaded.
Sealings: EPDM.
Mechanical Sealings: graphite-ceramic- EPDM
Employment 100% ED.
Ambient Temperature: 50 Degrees C.
Fluid Temperature: 60 Degrees C.
Suction Prevalence 0.
Fluids: Water and non corrosive media.
Pressure and flow rate (See diagram)
Power Supply A.C.
Power 50 Hz 180W (0 BAR) - 250W (3,5 bar)
Power 60 Hz 200W (0 BAR - 320W (4 bar)
CEME DISTRIBUTOR
Solenoid Valves, Switches & Pumps
General Features
Minimum differential working pressure: 0 Bar
Parts in contact with the fluid:
Sealing: NBR on request FPM - EPDM
EPDM - KTW sealing approved and DVGW certified
Body: Brass
Internal Parts: Stainless Steel
Fluids suitable: Air - Water - Light Oils.
One way direction valve.
Servicable Valve.
Valve Supplied with: -Three pole plug connector UNI ISO 4400
(DIN 43650A) - IP65
Mounting position: We advise installation of the valve with the coil
vertical. Models 8417, 8418, 8419 must be
mounted in the horizontal position with the coil
vertical.
Ambient temperature: 80 Degrees C. in DC
(current) for temperatures higher than 40
Degrees C, the performances (M.O.P.D.)
could decrease.
Special Executions - Version with water hammer device for slower
closing time.
- For models8415 and 8416, coil type B20 (30w) is
available to increase performances (M.O.P.D.) in
D.C. to 4 BAR pressue.